VISLONE 300W Electric Paint Sprayer User Manual

1. Važna sigurnosna uputstva

Pročitajte sva sigurnosna upozorenja, upute, ilustracije i specifikacije koje ste dobili uz ovaj električni alat. Nepoštivanje svih dolje navedenih uputa može dovesti do strujnog udara, požara i/ili ozbiljne ozljede.

• Sigurnost radnog područja: Radno područje održavajte čistim i dobro osvijetljenim. Ne koristite električne alate u eksplozivnim atmosferama, kao što je prisustvo zapaljivih tekućina, plinova ili prašine.
• električna sigurnost: Utikači električnih alata moraju odgovarati utičnici. Nikada ne modificirajte utikač ni na koji način. Izbjegavajte kontakt tijela sa uzemljenim površinama.
• Lična sigurnost: Always wear eye protection, respiratory protection, and appropriate clothing. Do not overreach. Maintain proper footing and balance at all times.
• Upotreba i njega alata: Ne forsirajte električni alat. Koristite odgovarajući električni alat za vašu primjenu. Isključite utikač iz izvora napajanja prije bilo kakvih podešavanja, promjene pribora ili skladištenja električnog alata.
• Specific Sprayer Safety: Ensure proper ventilation when spraying. Do not spray flammable materials near open flames or ignition sources. Always clean the sprayer thoroughly after each use.

2. Proizvod je gotovview i sadržaj paketa

The VISLONE 300W Electric Paint Sprayer is designed for efficient application of various coatings. Familiarize yourself with its components and ensure all items are present.

Slika 2.1: Gotovoview of the VISLONE 300W Electric Paint Sprayer.

2.1 Package List:

• 1 x Paint Sprayer
• 2 x Baterija (1300 mAh)
• 1 x četka za čišćenje
• 1 x igla za čišćenje
• 4 x Nozzles (Φ1.0mm, 1.8mm, 2.0mm, 2.5mm)
• 3 x Zaptivka
• 1 x Posuda za viskoznost
• 1 x Korisnički priručnik (ovaj dokument)
• 1 x punjač

3. Postavljanje i montaža

3.1 Priprema boje

1. Ensure the paint or coating material is suitable for spray application.
2. Use the provided viscosity cup to check the paint's viscosity. Thin the paint with the appropriate solvent (water for latex, mineral spirits for oil-based) until it passes through the viscosity cup within the recommended time (refer to paint manufacturer's instructions).
3. Strain the thinned paint to remove any lumps or debris that could clog the nozzle.

3.2 Sastavljanje prskalice

1. Attach the paint container (800ml tank) to the sprayer body by screwing it securely.
2. Insert a charged battery into the battery slot at the base of the handle until it clicks into place.

Figure 3.1: The 800ml capacity paint tank attached to the sprayer.

3.3 Selecting and Installing Nozzles

The sprayer includes four copper nozzles of different sizes (Φ1.0mm, 1.8mm, 2.0mm, 2.5mm) for various paint types and project requirements.

1. Choose the appropriate nozzle size for your paint and desired finish. Generally, smaller nozzles are for thinner materials and finer finishes, while larger nozzles are for thicker materials and faster coverage.
2. Unscrew the nozzle cap from the front of the sprayer.
3. Insert the selected nozzle and ensure a gasket is properly seated.
4. Screw the nozzle cap back on securely.

Figure 3.2: The four interchangeable copper nozzles (1.0mm, 1.8mm, 2.0mm, 2.5mm).

3.4 Podešavanje uzoraka prskanja

The sprayer offers three spray patterns: horizontal, vertical, and circular. Rotate the air cap to select the desired pattern.

• Horizontalno: For spraying up and down motions.
• okomito: For spraying side to side motions.
• cirkular: Za male površine ili detaljan rad.

4. Operacija

4.1 Powering On and Testing

1. Ensure the sprayer is fully assembled and the paint tank is filled.
2. Point the sprayer at a test surface (e.g., cardboard) and press the trigger to start spraying.
3. Adjust the flow control knob on the sprayer to achieve the desired paint output. The flow rate can be adjusted between 500-800ml/min.

Figure 4.1: Adjusting the flow control and selecting spray patterns (circular, horizontal, vertical).

4.2 Tehnika prskanja

• Održavajte dosljednu udaljenost (obično 6-12 cm) od površine koja se farba.
• Move the sprayer in smooth, even strokes, overlapping each pass by about 50% to ensure uniform coverage.
• Release the trigger at the end of each stroke to avoid paint buildup.
• For best results, apply multiple thin coats rather than one thick coat.

Slika 4.2: Pramples of the paint sprayer's application on furniture, walls, cars, and fences.

5. Održavanje i čišćenje

Proper cleaning after each use is essential to ensure the longevity and optimal performance of your paint sprayer.

5.1 Rastavljanje radi čišćenja

1. Disconnect the battery from the sprayer.
2. Unscrew the paint container and empty any remaining paint.
3. Unscrew the nozzle cap and remove the nozzle and gasket.
4. The front section of the sprayer can be easily detached from the motor housing for thorough cleaning.

Figure 5.1: The sprayer's design allows for easy disassembly for cleaning.

5.2 Postupak čišćenja

1. Fill the paint container with the appropriate cleaning solution (water for water-based paints, solvent for oil-based paints).
2. Reattach the container and spray the cleaning solution through the sprayer until it runs clear.
3. Thoroughly clean all disassembled parts (nozzle, gasket, container, suction tube) using the provided cleaning brush and needle.
4. Obrišite vanjski dio prskalice oglasnom folijomamp tkanina.
5. Ostavite sve dijelove da se potpuno osuše prije ponovnog sastavljanja ili skladištenja.

5.3 Skladištenje

Store the clean, dry sprayer in a cool, dry place, away from direct sunlight and extreme temperatures. Ensure the battery is removed if storing for extended periods.

6. Otkrivanje problema

7. Specifikacije

Figure 7.1: Dimensions of the VISLONE 300W Electric Paint Sprayer.

8. Garancija i podrška

For warranty information or technical support, please refer to the contact details provided by your retailer or visit the official VISLONE webSačuvajte račun kao dokaz o kupovini.

Možete posjetiti VISLONE Store on Amazon za više informacija.