Avisontek GK-BX G3T-BX Garage Door Opener Keypad and Remote Instruction Manual

1. Uvod

This manual provides comprehensive instructions for the installation, programming, and operation of your Avisontek GK-BX wireless garage door opener keypad and G3T-BX remote controls. These devices are designed to provide convenient and secure access to your garage.

Kompatibilnost: Compatible with all Genie and Overhead Door garage door openers manufactured since 1995 that utilize Intellicode technology. This system is a replacement for GK-R, GK-BX, GWKPD-BL, OKP-BX, GWK-IC, GWKP, ACSDA1, ACSDG, ACSD1G, B8QACSDA1, and B8QACSDA models. Note: Not compatible with Dip Switch openers.

This image illustrates the broad compatibility of the Avisontek GK-BX and G3T-BX with various Genie and Overhead Door Intellicode garage door openers manufactured from 1995 to the present. It also clearly indicates that the devices are not compatible with older Dip Switch openers.

2. Sigurnosne informacije

Please read and understand all safety warnings before installation and operation to prevent property damage or personal injury.

• Always keep the garage door opener and remote controls out of reach of children.
• Do not allow children to operate the keypad or remote.
• Ensure the garage door is visible and clear of obstructions before operating.
• Nikada ne hodajte ili trčite ispod pokretnih garažnih vrata.
• Baterije odložite na odgovarajući način u skladu sa lokalnim propisima.

3. Sadržaj paketa

Your Avisontek GK-BX G3T-BX package includes:

• 1 x GK-BX Wireless Keypad
• 2 x G3T-BX Remote Controls
• Mounting Hardware (for keypad)
• Uputstvo za upotrebu
• Batteries (2 AAA for keypad, 2 CR2032 for remotes - pre-installed)

4. Podešavanje i instalacija

4.1 Keypad Battery Installation

The GK-BX keypad comes with 2 AAA batteries pre-installed. If replacement is needed:

1. Open the keypad cover.
2. Locate the battery compartment on the back.
3. Remove the old batteries and insert two new AAA alkaline batteries, ensuring correct polarity.
4. Čvrsto zatvorite odeljak za baterije.

4.2 Ugradnja baterija u daljinski upravljač

The G3T-BX remotes come with CR2032 batteries pre-installed. If replacement is needed:

1. Use a small screwdriver to open the remote casing.
2. Replace the CR2032 battery, observing polarity.
3. Zatvorite daljinski upravljačasing sigurno.

This image displays the internal battery compartments for both the GK-BX keypad (using AAA batteries) and the G3T-BX remote (using a CR2032 battery), highlighting their high-capacity alkaline batteries for extended use.

4.3 Keypad Mounting

The GK-BX keypad is designed for wireless installation. Choose a convenient location outside your garage door, at least 5 feet above the ground, and away from moving parts of the door.

1. Open the keypad cover.
2. Mark the desired mounting holes using the keypad's backplate as a template.
3. Izbušite pilot rupe ako je potrebno.
4. Secure the keypad to the surface using the provided mounting screws.

This image demonstrates the wireless installation of the GK-BX keypad, highlighting its ease of setup without the need for complex wiring.

5. Programske instrukcije

Follow these steps carefully to program your keypad and remote controls.

5.1 Setting a Personal Identification Number (PIN) on the Keypad

1. Ensure the keypad backlight is off (do not press any buttons).
2. Pritisnite 3, 5, 7 keys on the keypad, then press the PROGRAM dugme.
3. The LED will blink. Now, enter a unique 3-8 digit PIN number.
4. Pritisnite PROGRAM ponovo dugme.
5. The keypad will blink twice and shut off, confirming successful PIN programming.

5.2 Syncing Keypad and Remote Controls with Your Garage Door Opener

There are typically two methods to put your garage door opener into programming mode. Refer to your garage door opener's manual for specific instructions or use the general guidance below.

Opener Programming Mode Option 1 (Genie Intellicode):

1. Pritisnite i držite PROGRAM button on your garage door opener until the LED indicator lights up.
2. Release the button. The round LED will turn off, and the long LED will begin flashing.
3. Proceed to step 2 in the 'Keypad to Opener Programming' section below.

Opener Programming Mode Option 2 (Genie Learn Code Button):

1. Pritisnite i otpustite LEARN CODE button on your garage door opener. The opener's LED will flash, indicating programming mode (typically for 30 seconds).
2. Proceed to step 2 in the 'Keypad to Opener Programming' section below.

5.3 Keypad to Opener Programming

1. Ensure the keypad backlight is off (do not press any buttons).
2. Enter your previously set PIN on the keypad.
3. Pritisnite UP or DOLJE arrow key on the keypad 3-4 times until the garage door opener activates. This confirms successful programming.

5.4 Remote Control to Opener Programming

1. Put your garage door opener into programming mode (refer to 5.2).
2. On the G3T-BX remote, press the desired button (top, middle, or bottom) you wish to program. The opener's light should flash or click, indicating it has learned the remote's code.
3. Test the remote by pressing the programmed button. The garage door should operate.

This image provides a visual guide to the programming steps for the GK-BX keypad, covering both PIN setup and synchronization with the garage door opener.

6. Operacija

6.1 Upotreba tastature

To operate your garage door using the GK-BX keypad:

1. Enter your 3-8 digit PIN.
2. Pritisnite GORE/DOLJE arrow key. The garage door will open or close.

The keypad features glow-in-the-dark buttons for easy visibility at night.

This image highlights the luminous design of the GK-BX keypad buttons, illustrating how they glow in the dark for convenient nighttime entry.

6.2 Korišćenje daljinskog upravljača

To operate your garage door using the G3T-BX remote:

1. Press the programmed button on the remote. The garage door will open or close.

The G3T-BX remote offers a range of up to 164 feet.

This image demonstrates the 3-channel control feature, allowing both the keypad and remote to operate up to three different garage door motors.

6.3 Temporary PIN for Guest Access

The GK-BX keypad supports a one-time temporary PIN feature for secure guest or delivery access. Consult the full programming instructions for details on setting up a temporary PIN.

7. Otkrivanje problema

If you encounter issues with your Avisontek garage door opener accessories, try the following:

• Uređaj ne reagira: Check battery levels in both the keypad and remote. Replace if necessary.
• Greška u programiranju: Ensure your garage door opener is in programming mode correctly. Repeat the programming steps carefully. Verify compatibility with your opener model (Intellicode only, not Dip Switch).
• Ograničeni raspon: Ensure there are no obstructions between the device and the garage door opener. Metal objects or thick walls can interfere with the signal.
• Pozadinsko osvjetljenje tastature ne radi: Provjerite baterije tastature.
• Door Opens/Closes Randomly: This is rare but could indicate interference. Try reprogramming the device.

8. Specifikacije

This image provides a visual summary of the technical specifications for both the GK-BX keypad and the G3T-BX remote, including physical dimensions and operational details.

9. Garancija i podrška

Your Avisontek GK-BX G3T-BX product is covered by a 3-godišnja garancija. For any questions, technical assistance, or warranty claims, please contact Avisontek customer support. Our team is available to provide friendly and helpful service.

This image highlights the available after-sales service, including 24-hour online tech support, FCC certification, a 3-year warranty, and the manufacturer's 15 years of experience.