XYWHPGV Pneumatic Push-to-Connect Elbow Connector

1. Proizvod je gotovview

The XYWHPGV Pneumatic Push-to-Connect Elbow Connector is designed for quick and secure connections in various pneumatic systems. This fitting features a 90-degree swivel angle, allowing for flexible positioning even after installation. It is constructed from durable plastic and brass, ensuring high strength, good sealing performance, and a long service life. The push-to-connect mechanism simplifies installation and removal of tubing.

This connector is primarily used in compressed air systems, vacuum systems, and general pneumatic applications. It is compatible with polyethylene, nylon, and PU pipes.

2. Karakteristike

• Univerzalni dizajn: Elbow Push-to-Connect Fitting with a 90-degree swivel angle male connector.
• Pipe & Thread Size: Designed for 10mm Outer Diameter (OD) pipes and 1/4PT external threads.
• Radni parametri: Supports an operating pressure range of 0-1MPa and an operating temperature range of 0°C to 60°C (32°F to 140°F).
• Izdržljiva konstrukcija: Made from high-quality plastic and brass for abrasion resistance, light weight, and resistance to squeezing, cracking, pressure, and corrosion.
• Sigurna veza: Features a robust trigger cap designed to withstand significant pressure without accidental disconnection.
• Svestrana upotreba: Suitable for connecting polyethylene, nylon, and PU pipes in various pneumatic applications.

3. Specifikacije

4. Postavljanje i instalacija

Follow these steps for proper installation of the push-to-connect elbow connector:

1. Pripremite cijev: Ensure that the cutting surface of the pipe is perfectly vertical and free from burrs or damage.
2. Umetnite cijev: Firmly insert the pipe into the push-to-connect end of the fitting. It is crucial to insert the pipe completely until it reaches the internal stop. Failure to do so may result in leaks.
3. Potvrdite vezu: After inserting the pipe, gently pull on the hose to confirm it is securely connected. If you cannot pull it out, the connection is properly established.
4. Navojni priključak: For the threaded end, apply appropriate thread sealant (e.g., PTFE tape) to the 1/4PT male thread before screwing it into the corresponding female port. Tighten sufficiently to create a seal, but do not overtighten.

5. Uputstvo za upotrebu

Once installed, the connector is ready for use within its specified operating parameters:

• Ensure the system pressure and temperature remain within the specified ranges of 0-1MPa and 0°C to 60°C (32°F to 140°F) respectively.
• The push-to-connect end allows for 360-degree rotation even after the pipe is inserted, providing flexibility in tubing alignment.

Disconnecting the Pipe:

To disconnect a pipe from the push-to-connect fitting:

1. Smanjite pritisak u sistemu: First, ensure that there is absolutely no pressure in the hose or the pneumatic system connected to the fitting. Attempting to disconnect under pressure can be dangerous and damage the fitting.
2. Press End Cap: Evenly press the end cap (release collar) of the fitting down towards the body of the connector.
3. Remove Pipe: While holding the end cap down, gently pull the pipe out of the fitting.

6. Održavanje

The XYWHPGV Pneumatic Push-to-Connect Elbow Connector is designed for long-term reliability with minimal maintenance. However, periodic checks are recommended:

• Vizuelni pregled: Regularly inspect the fitting for any signs of wear, cracks, or damage, especially around the pipe connection points and threads.
• Provjere curenja: Periodically check for air leaks around the connections. Leaks can indicate improper installation, worn seals, or damage to the fitting or tubing.
• čistoća: Keep the fitting clean and free from dirt, debris, or corrosive substances that could affect its performance or material integrity.
• Svojstva materijala: The plastic and brass construction provides good abrasion resistance and corrosion resistance, contributing to a long service life under normal operating conditions.

7. Otkrivanje problema

If you encounter issues with your pneumatic connector, consider the following:

• Leakage at Pipe Connection:
  • Ensure the pipe's cutting surface is vertical and smooth.
  • Verify the pipe is inserted completely into the fitting until it bottoms out.
  • Check the pipe for damage or deformation near the connection point.
• Leakage at Threaded Connection:
  • Confirm that thread sealant (e.g., PTFE tape) was properly applied.
  • Ensure the threaded connection is tightened adequately, but not excessively.
• Difficulty Disconnecting Pipe:
  • Ključno: Ensure the pneumatic system is fully depressurized before attempting to disconnect.
  • Press the release collar (end cap) evenly and firmly towards the fitting body while pulling the pipe.
• Fitting Damage: If the fitting shows visible signs of damage (cracks, deformation), it should be replaced immediately to prevent system failure or safety hazards.

8. Garancija i podrška

This product is manufactured by XYZOOM. For specific warranty information or technical support, please refer to the documentation provided at the point of purchase or contact your supplier. General warranty terms typically cover manufacturing defects under normal use conditions.

For further assistance, please contact the retailer or manufacturer with your product model number (f370edc35b08e0ddb2f00e6b5276ad) and purchase details.