KICKER 48TRTP122+CANDY-X1B+AMPKIT4

KICKER 48TRTP122 Subwoofer and DS18 CANDY-X1B AmpKorisnički priručnik za sistem lifier

Model: 48TRTP122+CANDY-X1B+AMPKIT4

1. Proizvod je gotovview

This manual provides instructions for the KICKER 48TRTP122 12-inch CompRT Down-Firing Loaded Subwoofer Enclosure, the DS18 CANDY-X1B Mono Class D Amplifier, and the accompanying DS18 AMPKIT4 4AWG Complete Amplifier Wiring Kit. This system is designed to enhance your vehicle's audio experience with powerful bass output.

2. Šta se nalazi u kutiji

  • Kicker 48TRTP122 12" CompRT Series Down-Firing Loaded Subwoofer Enclosure
  • DS18 CANDY-X1B Mono Candy-X Series Car Amplifier
  • DS18 AMPKIT4 4AWG Complete Amplifier Kit, including:
    • 17 ft 4 AWG Red Power Wire
    • 3 ft 4 AWG Black Ground Wire
    • 17 ft Remote Wire
    • 17 ft Red/Black Speaker Cable
    • 17 ft Red/Black Twisted RCA Cable
    • Mini ANL Fuse Holder with Mini ANL 100A Fuse
    • 6 ft 4 AWG Loom Tube
    • 1 x Rubber Grommet
    • 10 x kabelske vezice
    • 2 x prstenasti terminali
    • 2 x Spade terminala
    • 5 x Small Spade Terminals
Contents of the DS18 AMPKIT4 4AWG Complete Amplifier Kit, showing various wires, fuse holder, terminals, and cable ties.

Figure 2.1: Components of the DS18 AMPKIT4 4AWG Complete Amplifier Kit.

3. Postavljanje i instalacija

Pravilna instalacija je ključna za optimalne performanse i sigurnost. Ako niste sigurni u vezi s bilo kojim koracima, konsultujte se s profesionalnim instalaterom auto audio opreme.

3.1 Sigurnosne mjere

  • Prije početka bilo kakvih električnih radova, isključite negativni pol akumulatora vozila.
  • Osigurajte da su sve žice pravilno izolirane i osigurane kako biste spriječili kratke spojeve i oštećenja.
  • Koristite odgovarajuću ličnu zaštitnu opremu (LZO) tokom instalacije.

3.2 Subwoofer Enclosure Placement

The KICKER 48TRTP122 is a down-firing enclosure, designed to be placed in the trunk or cargo area of your vehicle. Ensure it is securely fastened to prevent movement during driving.

KICKER 48TRTP122 12-inch CompRT Down-Firing Loaded Subwoofer Enclosure, black carpeted finish.

Figure 3.1: KICKER 48TRTP122 Down-Firing Subwoofer Enclosure.

3.3 Ampmontiranje dizalice

Mount the DS18 CANDY-X1B amplifier in a location that allows for adequate ventilation and protection from moisture. Common locations include under a seat, in the trunk, or on the back of a rear seat. Ensure it is securely mounted to prevent vibration damage.

DS18 CANDY-X1B Mono Class D Amplifier, black with red accents.

Figure 3.2: DS18 CANDY-X1B Mono Class D Amplifier.

3.4 Upute za ožičenje

Follow these steps carefully for wiring the system. Refer to the wiring diagram below for visual guidance.

  1. Power Wire (Red 4 AWG): Run the 17 ft red power wire from the vehicle's positive battery terminal to the fuse holder, then from the fuse holder to the +12V terminal on the DS18 amplifier. Ensure the fuse holder is installed close to the battery (within 18 inches).
  2. Ground Wire (Black 4 AWG): Connect the 3 ft black ground wire from the GND terminal on the ampPričvrstite gornji dio na čistu, neobojenu metalnu površinu na šasiji vozila. Osigurajte dobru električnu vezu.
  3. Žica za daljinsko uključivanje: Connect the remote wire from your head unit's remote output to the REM terminal on the amplifier. This wire turns the ampuključivanje i isključivanje plamenika pomoću vaše glavne jedinice.
  4. RCA kablovi: Connect the RCA cables from your head unit's subwoofer output (or full-range output if no dedicated sub output) to the RCA input jacks on the DS18 amplifier.
  5. Žica zvučnika: Povežite kabl zvučnika sa amplifier's speaker output terminals to the KICKER subwoofer enclosure's input terminals. Ensure correct polarity (+ to + and - to -). The KICKER 48TRTP122 enclosure has a 2-ohm impedance.
  6. bas daljinski: Connect the included bass remote to the dedicated remote port on the DS18 amplifier. Mount the remote in an accessible location for easy adjustment.
Wiring diagram showing a 2-ohm subwoofer connected to a 2-ohm amplifier output, with positive and negative terminals clearly marked.

Figure 3.3: Subwoofer to Amplifier Wiring Diagram (2-ohm connection).

DS18 Bass Remote control unit with a rotary knob and connected cable.

Figure 3.4: DS18 Bass Remote Control.

4. Uputstvo za upotrebu

Once the system is installed, follow these steps to configure and operate your subwoofer and amplifier.

4.1 Initial Power-Up and Gain Setting

  1. Ponovo spojite negativni pol akumulatora vozila.
  2. Uključite glavnu jedinicu. amplifier should power on (indicated by a blue LED on the amplifier).
  3. Postavite amplifier's GAIN control to its minimum (fully counter-clockwise) position.
  4. Play a music track with strong bass at a moderate volume level on your head unit (around 75% of maximum volume).
  5. Slowly increase the GAIN control on the amplifier until you hear distortion, then back it off slightly until the sound is clear. This sets the maximum clean output level.

4.2 Amplifier Controls (DS18 CANDY-X1B)

The DS18 CANDY-X1B amplifier features several controls for fine-tuning your bass output:

  • DOBITAK: Adjusts the input sensitivity to match the output of your head unit. (See 4.1)
  • BASS BOOST (0-18 dB): Increases the bass output at a specific frequency (typically around 45 Hz). Use sparingly to avoid distortion and speaker damage.
  • LPF (Low-Pass Filter) (50-150 Hz): This filter allows only frequencies below the set point to pass through to the subwoofer. Adjust to blend the subwoofer's output seamlessly with your main speakers.
  • SUBSONIC FILTER (10-55 Hz): Filters out extremely low frequencies that are inaudible and can cause damage to the subwoofer. Set it slightly below your subwoofer's lowest usable frequency.
  • PHASE (0/180 degrees): Adjusts the phase of the subwoofer output relative to your main speakers. Experiment with both settings to find the one that provides the most impactful and coherent bass.
  • DALJINSKO: Port for connecting the wired bass remote control, allowing convenient bass level adjustment from the driver's seat.
Close-up of the DS18 CANDY-X1B amplifier's control panel, showing gain, bass boost, LPF, subsonic filter, and phase controls.

Figure 4.1: DS18 CANDY-X1B Amplifier Controls.

5. Održavanje

Regular maintenance ensures the longevity and optimal performance of your audio system.

  • čišćenje: Keep the subwoofer enclosure and amplifier clean and free of dust and debris. Use a soft, dry cloth. Avoid liquid cleaners directly on components.
  • Veze: Povremeno provjeravajte sve spojeve ožičenja na čvrstoću i koroziju. Labavi spojevi mogu dovesti do loših performansi ili oštećenja.
  • ventilacija: Osigurajte amplifier's cooling fins are not obstructed to prevent overheating.
  • Provjera osigurača: Ako je amplifier does not power on, check the fuse in the fuse holder near the battery. Replace with a fuse of the same rating (100A Mini ANL).

6. Otkrivanje problema

Pogledajte ovaj odjeljak za uobičajene probleme i njihova rješenja.

ProblemMogući uzrokRješenje
Nema zvuka iz subwoofera
  • Nema snage za amplifier
  • Labavi RCA ili zvučnički priključci
  • Postavke glavne jedinice
  • Ampspasilac u zaštitnom režimu
  • Check power, ground, and remote wires. Verify fuse.
  • Ensure all RCA and speaker wires are securely connected.
  • Check head unit's subwoofer output settings and volume.
  • Isključite i ponovo pokrenite amplifier. Check for shorts in speaker wiring.
Izobličen zvuk
  • Pojačanje postavljeno previsoko
  • Bass boost too high
  • Isečak sa glavne jedinice
  • Oštećena žica zvučnika
  • Smanji amplifier gain.
  • Lower bass boost setting.
  • Reduce head unit volume.
  • Pregledajte žice zvučnika da li imaju oštećenja ili kratkih spojeva.
AmpLifier se pregreva
  • Nedovoljna ventilacija
  • Nepravilno impedantno opterećenje
  • Pojačanje postavljeno previsoko
  • Osigurati amplifier has clear airflow.
  • Provjerite podudaranja impedanse subwoofera amplifier's stable load (2 ohms for this system).
  • Smanji amplifier gain.
Bass remote not working
  • Slaba veza
  • Oštećen kabl
  • Check the connection of the remote cable to the amplifier.
  • Pregledajte kabel za vidljiva oštećenja.

7. Specifikacije

Detailed specifications for the components in this bundle.

7.1 KICKER 48TRTP122 12" CompRT Subwoofer Enclosure

  • Vrsta zvučnika: Subwoofer
  • Prečnik subwoofera: 12 inča
  • Vršna snaga: 1000 vati
  • RMS snaga: 500 vati
  • impedansa: 2 oma
  • Osjetljivost: 98dB
  • Posebna karakteristika: Down-Firing, Active thin-mount CompRT subwoofer, High-output reFLEX passive woofer
  • Materijal: Vlaknaste ploče srednje gustine
  • Dimenzije: 27.5" W x 6.125" H x 14.625" D (Top) x 14.625" D (Bottom)

7.2 DS18 CANDY-X1B Mono Class D Amplifier

  • RMS snaga snage:
    • 4 oma: 240 vati x 1 kanal
    • 2 oma: 400 vati x 1 kanal
    • 1 ohm: 600 vati x 1 kanal
  • Maksimalna izlazna snaga: 1800 vati
  • Osjetljivost: 100dB
  • Frekvencijski odziv: 20-150 Hz
  • bas daljinski: Uključeno
  • Dizajn: Klasa D
  • Varijabilno pojačanje basa: 0-18 dB
  • Variable Low-pass filter (LPF): 50-150 Hz
  • Podzvučni filter: 10-55 Hz
  • Dimenzije: 5.9" Š x 8.3" D x 2.16" V

7.3 DS18 AMPKIT4 4AWG Complete Amplifier Kit

  • Žica mjerač: 4 AWG
  • Materijal žice: High Performance CCA (Copper Clad Aluminum)
  • Preporučuje se za: Jedan amplifier up to 1300 Watts
  • Uključene komponente: Power wire, ground wire, remote wire, speaker cable, RCA cable, fuse holder with 100A fuse, loom tube, grommet, cable ties, various terminals.

8. Informacije o garanciji

This product bundle typically comes with a manufacturer's warranty. The KICKER 48TRTP122 subwoofer enclosure and DS18 CANDY-X1B amplifier are covered by a full warranty from their respective manufacturers. Specific warranty terms, duration, and coverage details may vary. Please retain your proof of purchase for warranty claims.

For detailed warranty information, refer to the documentation included with each individual component or visit the respective manufacturer's official website.

9. Podrška

If you encounter issues not covered in this manual or require further assistance, please contact the manufacturer's customer support:

  • KICKER Support: Visit the official KICKER webstranica za resurse podrške, često postavljana pitanja i kontakt informacije.
  • DS18 Support: Visit the official DS18 website for product support and contact details.

When contacting support, please have your product model numbers (48TRTP122, CANDY-X1B, AMPKIT4) and proof of purchase readily available.