1. Proizvod je gotovview
The Dayton Audio DTA-100LF is a compact desktop amplifier specifically engineered for low-frequency applications. This amplifier delivers robust performance with 100 watts of power at 4 ohms, making it suitable for driving subwoofers or bass shakers. Its low-profile design integrates seamlessly into various setups, from desktops to under-desk installations using the included mounting brackets. Key features include adjustable phase, a subsonic filter, a low-pass filter, and a single-band equalizer to fine-tune audio output. The amplifier also incorporates an auto-on function for convenient, set-and-forget operation, automatically powering on when an audio signal is detected and entering standby when inactive.
2. Sigurnosne informacije
- Izvor napajanja: Povežite amplifier only to the specified power supply (120-240 VAC).
- ventilacija: Osigurajte odgovarajuću ventilaciju oko uređaja kako biste spriječili pregrijavanje. Ne blokirajte ventilacijske otvore.
- Vlaga: Ne izlažite uređaj kiši, vlazi ili prekomjernoj vlažnosti.
- čišćenje: Disconnect power before cleaning. Use a dry, soft cloth. Avoid liquid cleaners.
- servisiranje: Ne pokušavajte sami servisirati ovaj proizvod. Sve servise prepustite kvalificiranom servisnom osoblju.
3. Kontrole i veze
3.1 Kontrole na prednjoj ploči
Image: Front panel view of the DTA-100LF, showing the EQ controls and power indicator.
- DOBITAK: Podešava ulaznu osetljivost amplifier.
- LOW PASS FREQ: Sets the upper frequency limit for the amplifier's output (30 Hz - 200 Hz).
- FAZA: Adjusts the phase of the output signal (0° - 180°).
- EQ FREQ: Selects the center frequency for the single-band parametric equalizer.
- EQ BANDWIDTH: Adjusts the width of the frequency band affected by the EQ.
- EQ NIVO: Controls the boost or cut at the selected EQ frequency.
3.2 Priključci stražnje ploče
Image: Rear panel view of the DTA-100LF, displaying RCA line inputs/outputs, speaker outputs, and power input.
- AUTO ON / ON / OFF Switch: Selects the power mode (Auto-On, Always On, Off).
- LINIJSKI IZLAZ (RCA): Stereo RCA izlazi za povezivanje s drugim ampuređaj za spašavanje ili spašavanje.
- LINIJSKI ULAZ (RCA): Stereo RCA inputs for connecting audio sources.
- SUBSONIC FILTER: Rotary control to adjust the subsonic filter frequency.
- OUTPUT (Speaker Terminals): Connects to your passive subwoofer or bass shaker. Supports 4 ohm minimum impedance.
- Prekidač za UKLJUČIVANJE/ISKLJUČIVANJE: Glavni prekidač za napajanje.
- Ulaz napajanja: Connects to the provided AC power cord (120-240 VAC).
4. Podešavanje
4.1 Povezivanje audio izvora
- Ensure the DTA-100LF is powered off.
- Connect your audio source (e.g., receiver, preamplifier) na LINE IN (RCA) jacks on the rear panel using appropriate RCA cables.
- If connecting to another amplifier, use the LINE OUT (RCA) utičnice.
4.2 Povezivanje zvučnika
- Connect your passive subwoofer or bass shaker to the OUTPUT (Speaker Terminals) na zadnjoj ploči.
- Ensure correct polarity (red to red, black to black). The amplifier supports a minimum impedance of 4 ohms.
4.3 Povezivanje napajanja
- Connect the provided AC power cord to the POWER Input na zadnjoj ploči.
- Plug the other end of the power cord into a suitable electrical outlet (120-240 VAC).
4.4 Montiranje (opciono)
Image: Included mounting brackets and power cable, illustrating accessories for installation.
The DTA-100LF includes mounting brackets for installation under desks or tables. Securely attach the brackets to a flat surface using appropriate screws (not included), then slide the amplifier into place.
5. Uputstvo za upotrebu
5.1 Uključivanje/isključivanje
- Koristite Prekidač POWER ON / OFF on the rear panel for main power control.
- For automatic operation, set the AUTO ON / ON / OFF Switch to AUTO ON. The amplifier will power on when an audio signal is detected and enter standby after a period of inactivity.
- For continuous operation, set the AUTO ON / ON / OFF Switch to ON.
5.2 Adjusting Audio Output
- DOBITAK: Start with the GAIN control at its minimum setting and gradually increase it until the desired volume is achieved without distortion.
- LOW PASS FREQ: Adjust this control to blend the subwoofer's output smoothly with your main speakers. A common starting point is 80-100 Hz.
- FAZA: Experiment with the PHASE control (0° - 180°) to achieve the best bass response and integration with your main speakers.
- SUBSONIC FILTER: Use this to protect your drivers from over-excursion by filtering out extremely low frequencies below their safe operating range.
- EQ Controls (FREQ, BANDWIDTH, LEVEL): Utilize the single-band parametric EQ to address specific room modes or frequency peaks/dips. Adjust FREQ to target the problematic frequency, BANDWIDTH to control the affected range, and LEVEL to boost or cut.
6. Održavanje
- čišćenje: Zadrži amplifier clean by wiping it with a soft, dry cloth. Do not use abrasive cleaners or solvents.
- ventilacija: Ensure that the ventilation holes are free from dust and obstructions to maintain proper airflow.
- Skladištenje: Ako uređaj skladištite duži period, isključite ga iz napajanja i čuvajte ga na hladnom i suhom mjestu.
7. Otkrivanje problema
| Problem | Mogući uzrok | Rješenje |
|---|---|---|
| Nema struje | Kabel za napajanje nije priključen; Prekidač isključen; Kvar utičnice. | Check power cord connection; Ensure POWER ON/OFF switch is ON; Test outlet with another device. |
| Nema zvuka | Input source not connected; GAIN too low; Speaker wires loose; AUTO ON mode inactive. | Check RCA LINE IN connections; Increase GAIN; Secure speaker wires; Switch AUTO ON to ON. |
| Izobličen zvuk | GAIN too high; Speaker impedance mismatch; Faulty cables. | Reduce GAIN; Ensure speaker impedance is 4 ohms minimum; Replace cables. |
| Auto-On not working | Input signal too low; AUTO ON switch not engaged. | Increase volume from source; Ensure AUTO ON switch is selected. |
8. Specifikacije
- Maksimalna izlazna snaga: 70 Watts @ 8 ohms, 100 Watts @ 4 ohms
- THD: <1%
- Frekvencijski odziv: 20 Hz - 180 Hz +/- 3dB
- SNR: 95dB
- Ulazna osjetljivost: 200mV
- Line Input Connectors: RCA
- Line Output Connectors: RCA
- Low Pass Crossover Range: 30 Hz - 200 Hz
- Podešavanje faze: 0° - 180° Variable
- Ulazna impedancija: 22 kOhm
- Line Output Impedance: 4 kOhm
- Ulazna snaga Voltage Raspon: 120 - 240 V AC
- Snaga u stanju pripravnosti: 1.8 Watts
- Maksimalna potrošnja energije: 150 Watts
- Dimenzije (Š x V x D): 7.5″ Š x 2″ V x 5.5″ D
- Težina: 3.3 lbs.
9. Garancija i podrška
The Dayton Audio DTA-100LF is backed by a 5-year warranty on both parts and labor, reflecting our commitment to quality and reliability. For technical support, troubleshooting assistance, or warranty claims, please contact Dayton Audio customer service through our official website or the retailer where the product was purchased. Please have your model number (DTA-100LF) and proof of purchase ready when contacting support.