DAKASON 4FT LED Vapor Tight Light Instruction Manual

1. Uvod

This manual provides detailed instructions for the safe installation, operation, and maintenance of your DAKASON 4FT LED Vapor Tight Light. Please read this manual thoroughly before installation and retain it for future reference.

The DAKASON 4FT LED Vapor Tight Light is a high-efficiency lighting fixture designed for demanding environments. It features adjustable wattage (40W/50W/60W), 0-10V dimming capability (dimmer not included), and an IP65 rating for resistance against water, dust, and harsh conditions.

2. Sigurnosne informacije

WARNING: Risk of electric shock. Installation must be performed by a qualified electrician in accordance with all national and local electrical codes.

• Isključite napajanje na osiguraču ili prekidaču strujnog kruga prije instalacije ili servisiranja.
• Osigurajte dovod voltage is compatible with the fixture (100-277V).
• Do not handle live wires.
• Uvjerite se da su svi priključci sigurni i pravilno izolirani.
• Nemojte modificirati učvršćenje.
• Nosite odgovarajuću ličnu zaštitnu opremu (LZO) tokom instalacije.
• This fixture is designed for indoor/outdoor use in wet, damp, and dusty areas.

3. Sadržaj paketa

Prije početka instalacije provjerite da li su sve komponente prisutne:

• 1 x 4FT LED Vapor Tight Lighting Fixture
• 10 x Stainless Steel Clips
• 2 x montažni nosači
• 4 x Plastic Wall Plugs
• 4 x Vijci
• 1 x Waterproof Cable Gland

Figure 3.1: Included mounting kit and components.

4. Specifikacije

Figure 4.1: IP65 rating details for the vapor tight light.

5. Upute za instalaciju

This fixture supports surface/wall mount and suspension mount (additional accessories required for suspension). The following steps detail surface/wall mounting.

1. Isključite napajanje: Before starting, ensure electrical power is turned off at the fuse or circuit breaker box to prevent electric shock.
2. Mark mounting locations: Use the mounting brackets to mark the desired locations for drilling holes on the mounting surface.
3. Install mounting brackets: Drill holes and secure the mounting brackets to the surface using the provided screws and wall plugs.
4. Pripremite ožičenje: Open the fixture housing. Feed the supply wire (not included) through the waterproof cable gland. Select the desired wattage (40W/50W/60W) using the internal switch.
5. Žične veze: Connect the supply wires to the LED driver according to the wiring diagram.
   • Black (Line) to L
   • White (Neutral) to N
   • Green (Ground) to Gnd
   • Purple (Dim+) and Gray (Dim-) for 0-10V dimming control (if applicable).
   Tighten the external nut on the waterproof cable gland to ensure a water-tight seal.
6. Pričvršćivač za montažu: Lift the fixture housing and snap it into place on the installed mounting brackets.
7. Secure lens: Position the lens onto the fixture housing and secure it with the stainless steel latches/clips. Ensure the lens is tightly sealed with the housing to maintain the vapor-tight integrity.

Figure 5.1: Hard-wired installation steps and wiring diagram.

6. Uputstvo za upotrebu

Once installed and wired correctly, the DAKASON LED Vapor Tight Light is ready for operation.

• Uključeno: Restore power at the circuit breaker. The light will illuminate.
• Wattage Izbor: The fixture has a selectable wattage switch (40W/50W/60W) located inside the housing. Adjust this switch prije sealing the fixture and restoring power to set the desired light output.
  

  Figure 6.1: Internal wattage prekidač za izbor.
• Funkcija zatamnjivanja: If connected to a compatible 0-10V dimmer switch (not included), the light output can be adjusted from 0% to 100%.

  Video 6.1: Demonstration of 0-10V dimming capability in a warehouse setting.

7. Održavanje

The DAKASON LED Vapor Tight Light is designed for minimal maintenance. Follow these guidelines to ensure optimal performance and longevity:

• čišćenje: Povremeno čistite vanjski dio uređaja mekom,amp cloth. Do not use abrasive cleaners or solvents, as these can damage the polycarbonate housing and lens. Ensure power is off before cleaning.
• inspekcija: Regularly inspect the fixture for any signs of damage, loose connections, or wear. Pay attention to the waterproof cable gland and stainless steel clips to ensure the seal remains intact.
• Nema dijelova koje može servisirati korisnik: There are no user-serviceable parts inside the fixture. Do not attempt to open or repair the LED driver or LED chips. Contact qualified personnel for any repairs.

8. Otkrivanje problema

If you experience issues with your DAKASON LED Vapor Tight Light, refer to the following troubleshooting guide:

If the problem persists after attempting these solutions, please contact DAKASON customer support.

9. Garancija i podrška

DAKASON provides a 5 godine garancije for this LED Vapor Tight Light, covering defects in materials and workmanship under normal use.

For warranty claims, technical support, or any questions regarding your product, please contact DAKASON customer service through the retailer where the product was purchased or visit the official DAKASON webstranica za kontakt informacije.

Please have your model number (VPD-4A-50KFD) and purchase date available when contacting support.