Auto Ventshade [AVS] Aeroskin Hood Protector Instruction Manual

Product Overview

The AVS Aeroskin Hood Protector is designed to provide ultimate protection from road hazards while seamlessly integrating with your vehicle's contours for a sleek, aerodynamic appearance. It features the lowest profile design on the market, creating a skin-tight barrier for your hood. Installation is straightforward, requiring no drilling or special hardware, and utilizes pre-applied 3M automotive-grade adhesive.

Ključne karakteristike:

• FITMENT: Specifically designed for 2019 - 2025 Chevrolet Blazer models.
• LOW PROFILE: Offers the lowest profile protection available, constructed from impact-modified acrylic.
• SKINTIGHT: Shields your vehicle from road hazards with a protective, hood-hugging fit.
• CUSTOMIZED FIT: Engineered to fit the exact year, make, and model of your vehicle, complementing its appearance.
• LAKO ZA UGRADNJU: No drilling or special hardware required. Mounts in minutes using pre-applied 3M automotive-grade adhesive tape.

Image: The AVS Aeroskin Hood Protector in a chrome finish, designed for a low-profile fit.

Vodič za instalaciju

Installation of the AVS Aeroskin Hood Protector is designed to be simple and requires no drilling. Follow these steps carefully to ensure proper fit and adhesion.

Image: A visual guide detailing the six steps for installing the Aeroskin Hood Protector, including surface preparation, tape application, and final pressing.

Instalacija korak po korak:

1. 1. Prepare the Surface:

   Start with a clean truck. Ensure the installation is done at room temperature. Properly prepare the surface area to ensure automotive tape bonds best. Dry fit the protector and outline the area with painter's tape.

2. 2. Clean the Leading Edge:

   Use alcohol pads to clean the entire leading edge of the hood where the protector will be applied.

3. 3. Peel Back Tape Liners:

   Peel back approximately 2 inches of the tape liner from the ends of the protector. Ensure you can easily access the free ends of the tape liner for later removal.

4. 4. Center and Test Fit:

   Center and test fit the hood protector. Do not apply pressure yet until it's evenly set on the hood area. Use the painter's tape outline as a guide.

5. 5. Remove Remaining Tape Liners:

   Remove the tape liner starting with the center top. Grasp the free tape ends that you peeled back in step 3 and gently pull them while applying firm pressure with your free hand to the protector as it adheres.

6. 6. Secure Adhesion:

   Press firmly along the entire length of the protector to ensure complete adhesion to the hood. Apply consistent pressure.

Important: Do not drive for 24 hours or wash your vehicle for 72 hours after installation to allow the adhesive to fully cure.

Njega i održavanje

To maintain the appearance and longevity of your AVS Aeroskin Hood Protector, regular cleaning is recommended. Use mild automotive soap and water with a soft cloth or sponge. Avoid abrasive cleaners or harsh chemicals that could damage the finish. For chrome finishes, use products specifically designed for chrome to prevent scratching and maintain shine. Ensure the protector is dry after washing.

Rješavanje problema

Problemi s prianjanjem:

If the hood protector does not adhere properly, ensure the surface was thoroughly cleaned with alcohol and that the adhesive promoter (if included and used) was applied correctly. Temperature during installation is critical; ensure it is at room temperature. Apply firm, even pressure across the entire adhesive surface during installation.

Scratches or Dullness (Chrome Finish):

Chrome finishes can be susceptible to fine scratches if not cleaned with appropriate materials. Avoid abrasive cloths or harsh cleaning agents. Use soft microfiber cloths and chrome-specific cleaning solutions. If the finish appears dull, a chrome polish designed for automotive use may restore its luster.

Specifikacije proizvoda

Sadržaj paketa

• Hood Shield
• Uputstva

Garancija i podrška

For specific warranty information and support regarding your AVS Aeroskin Hood Protector, please contact Auto Ventshade directly. Details are typically provided with your product packaging or can be found on the manufacturer's official website.

Proizvođač: Auto Ventshade

For further assistance, please refer to the contact information provided by the manufacturer.