DollaTek LD35 USB Electronic Load Tester Instruction Manual

1. Uvod

The DollaTek LD35 is a versatile USB electronic load tester designed for constant current discharge testing. It features a user-friendly interface and robust performance indicators, suitable for various testing requirements. This device can handle constant discharge tasks up to 4A, 25V, and 35W. It is equipped with a 4-bit LED digital display for real-time monitoring of voltage, current, and power values, and includes Micro USB and Type-C input ports for comprehensive testing of charging cables.

Key features include precise current adjustment, an efficient all-aluminum heat sink with an intelligent temperature-controlled fan, and multiple protection mechanisms against over-voltage, over-current, and high temperatures.

2. Sigurnosne informacije

WARNING: The input polarity cannot be reversed. Reversing the input polarity will permanently damage the product and it cannot be repaired.

To ensure safe operation and prevent damage to the device or connected equipment, please observe the following:

• Do not exceed the maximum rated operational voltage of DC 4-25.0V.
• Do not exceed the maximum discharging power of 35W.
• The device includes built-in protection against over-voltage (OVP), over-power (OPP), and over-temperature (OTP). If any of these limits are exceeded, the device will automatically display a relevant code and stop discharging to prevent damage.
• Ensure proper ventilation around the device, especially when operating at higher loads, to allow the fan to dissipate heat effectively.
• When testing power banks, carefully check their output current capabilities. Adjust the load current to a smaller value if the power bank's output is limited to prevent damage to the power bank.

3. Proizvod je gotovview

The DollaTek LD35 USB Electronic Load Tester features a compact design with essential controls and indicators for efficient testing.

Slika 3.1: Prednja strana view of the LD35 USB Electronic Load Tester, showing the fan, LED display, and control buttons.

Figure 3.2: The LD35 Intelligent Electronic Load, highlighting the fan and digital display.

Slika 3.3: Pozadi view of the LD35 circuit board, showing internal components.

3.1 Komponente

• USB-A Input Connector: For connecting to the power source under test.
• Mikro USB ulazni port: Additional input for testing Micro USB cables.
• Ulazni port tipa C: Additional input for testing Type-C cables.
• 4-bit LED Display: Prikazuje jačinu zvuka u realnom vremenutage, current, and power values.
• Adjustable Potentiometer: Used to precisely adjust the discharge current.
• "ON/OFF" Button: Toggles the load output on or off.
• "SET" Button: Cycles through display modes (Voltage, Current, Power) and is used for setting boot status and recovery.
• ventilator za hlađenje: Intelligent temperature-controlled fan for heat dissipation.
• hladnjak: All-aluminum heat sink for efficient thermal management.

Figure 3.4: Dimensions of the LD35 USB Electronic Load Tester (83.8mm x 41.1mm x 27.9mm).

4. Podešavanje

Setting up the LD35 is straightforward:

1. Povežite izvor napajanja: Insert the USB-A connector of the LD35 into the USB output port of the power source you wish to test (e.g., power bank, USB charger, computer USB port). Alternatively, use the Micro USB or Type-C input ports to test corresponding cables by connecting them to a power source and then to the LD35.
2. Početni prikaz: Upon connection, the LED display will light up, showing the current setting value. This indicates the device is powered on and waiting for output.
3. Potvrdite vezu: Ensure the connection is secure and stable.

5. Uputstvo za upotrebu

The LD35 offers intuitive controls for managing the load and monitoring parameters.

Figure 5.1: Diagram illustrating the operational controls and functions of the LD35.

5.1 Open or Close Load Output

• Pritisnite "UKLJUČENO/ISKLJUČENO" button to toggle the load output. When the load is active, the device will begin drawing current according to the set value.

5.2 Adjust Output Current Value

• Rotirajte adjustable potentiometer (blue knob) clockwise to increase the current value and counter-clockwise to decrease it.
• The potentiometer allows for both coarse and fine adjustments. The fine adjustment capability ensures precise current setting, down to 0.01A, preventing accidental damage from sudden large current changes.

5.3 Adjust LED Display Status

• Pritisnite "POSTAVI" button to cycle through the displayed parameters: current (A), power (P), and voltage (V). The default display shows the output current value.

5.4 Set Load Default Boot Status

• To set the default boot status (open or close load), press and hold the "UKLJUČENO/ISKLJUČENO" dugme.
• If the LED displays "ON", the load will automatically open output when powered on next time.
• If the LED displays "OFF", the load will remain closed on power-up. To open the load, press the "ON/OFF" button.

5.5 Set Load Output Recovery Mode After Protection

• If the device enters a protection state (OVP, OPP, OTP), the LED display will show a relevant error code.
• To set the recovery mode, press and hold the "POSTAVI" dugme.
• If the LED displays "ON", the load will automatically recover to work after the protection condition is removed.
• If the LED displays "OFF", the protection will be removed, but the load will remain closed. You must then press the "ON/OFF" button to resume operation.

NOTE: When testing power banks, always check their output current capacity. For power banks with generally small output currents, adjust the load to a smaller current value to prevent damage.

6. Specifikacije

The following table details the technical specifications of the DollaTek LD35 USB Electronic Load Tester:

Figure 6.1: Detailed product parameters for the LD35.

7. Otkrivanje problema

This section addresses common issues you might encounter with the LD35 USB Electronic Load Tester.

7.1 Protection Triggered (OVP, OPP, OTP)

• Simptom: The LED display shows an error code (e.g., OVP, OPP, OTP) and the load output stops.
• Uzrok: Ulazni voltage, power, or internal temperature has exceeded the safe operating limits.
• Rješenje:
  1. Isključite izvor napajanja.
  2. Identify and resolve the cause (e.g., use a power source within the specified voltage range, reduce the set current to lower power, ensure adequate ventilation).
  3. If the recovery mode is set to "ON" (see Section 5.5), the device will automatically resume operation once the condition is resolved. If set to "OFF", press the "ON/OFF" button to restart the load.

7.2 Fan Not Operating or Stuttering

• Simptom: The cooling fan does not spin or stutters during operation.
• Uzrok: The fan is temperature-controlled and will only activate when the internal temperature reaches a certain threshold. If the input voltage drops too low (e.g., below 4.5V), the fan may not receive sufficient power to operate correctly.
• Rješenje:
  1. Verify that the device is drawing sufficient current to generate heat, which would trigger the fan.
  2. Osigurajte ulaznu voltage from the power source is stable and within the operational range (DC 4-25.0V). If the voltage sags under load, the fan might stop.
  3. Provjerite ima li prepreka na lopaticama ventilatora.

7.3 Netačna očitavanja

• Simptom: Prikazani voltage, current, or power values appear incorrect.
• Uzrok: External factors, faulty connection, or device malfunction.
• Rješenje:
  1. Uvjerite se da su svi spojevi sigurni i bez korozije.
  2. Compare readings with a calibrated multimeter if available.
  3. Ensure the device is operating within its specified parameters.

8. Održavanje

The DollaTek LD35 USB Electronic Load Tester requires minimal maintenance to ensure long-term performance.

• čišćenje: Use a soft, dry cloth to clean the exterior of the device. Do not use liquid cleaners or solvents. Ensure no dust or debris accumulates in the fan or heat sink fins, as this can impede cooling.
• Skladištenje: Uređaj čuvajte na hladnom i suhom mjestu, dalje od direktne sunčeve svjetlosti i ekstremnih temperatura.
• Rukovanje: Handle the device with care to avoid physical damage, especially to the USB connectors and potentiometer.

9. Podrška i garancija

For technical support or inquiries regarding the DollaTek LD35 USB Electronic Load Tester, please refer to the manufacturer's resources.

An instruction PDF can be found by scanning the QR code on the fan or by visiting the following link:

DollaTek LD35 Instruction PDF

This document provides additional details and diagrams that may be helpful for advanced users.

Proizvođač: DollaTek

Warranty information is typically provided at the point of purchase or through the retailer. Please retain your proof of purchase for any warranty claims.