Product Overview
This manual provides detailed instructions for the proper use, installation, and maintenance of the Molex KK 396 Series Connector, Model 09-48-1054. This connector is a 5-position, single-row receptacle with a 3.96mm pitch, designed for board-to-board applications and through-hole right-angle mounting. It is part of the KK 396 41815 Series and is RoHS compliant.
Image: A Molex KK 396 Series 5-position connector receptacle (Model 09-48-1054). This image shows the white plastic housing with five contact points, designed for through-hole right-angle mounting.
Sigurnosne informacije
Always observe the following safety precautions when handling and installing the connector:
- Ensure power is disconnected from the circuit before installation or removal.
- Handle components with care to avoid damage to pins or housing.
- Refer to relevant industry standards and local regulations for electrical installations.
- Do not modify the connector. Use only as intended.
Postavljanje i instalacija
The Molex KK 396 Series Connector (09-48-1054) is designed for through-hole right-angle mounting on a printed circuit board (PCB). Follow these steps for proper installation:
- Pripremite PCB ploču: Ensure the PCB has the correct hole pattern and dimensions for the 5-position, 3.96mm pitch connector.
- Orient the Connector: Carefully align the connector pins with the corresponding holes on the PCB. Note the right-angle orientation.
- Umetnite konektor: Gently push the connector into the PCB holes until it sits flush with the board surface. Avoid excessive force.
- Priključci za lemljenje: Solder each pin to its respective pad on the PCB. Ensure good solder joint integrity, free from bridges or cold joints. Use appropriate soldering techniques and equipment.
- Pregledajte instalaciju: Visually inspect all solder joints and the connector's seating on the PCB to ensure proper installation.
For optimal performance, ensure the mating connector (e.g., Molex KK 396 Series header) is correctly aligned and engaged.
Operativni principi
The Molex KK 396 Series Connector facilitates reliable electrical connections between two circuit boards or between a board and a wire harness. Its operation is passive, serving as a conduit for electrical signals and power.
- veza: The receptacle (Model 09-48-1054) mates with a compatible Molex KK 396 Series header. Ensure proper alignment before mating to prevent pin bending or damage.
- Isključivanje: To disconnect, gently pull the mating connector straight away from the receptacle. Avoid twisting or prying, which can damage the contacts or housing.
- Current and Voltage: Adhere to the specified current and voltage ratings for the KK 396 series to prevent overheating or electrical failure. Consult the Molex datasheet for detailed electrical characteristics.
Održavanje
The Molex KK 396 Series Connector is designed for long-term reliability with minimal maintenance. However, periodic inspection can help ensure continued performance.
- čišćenje: If necessary, clean the connector contacts using a lint-free cloth and a suitable electronic contact cleaner. Ensure the cleaner is non-residue and safe for plastics.
- inspekcija: Periodically inspect the connector for signs of physical damage, corrosion, or loose connections. Check for bent or broken pins, cracks in the housing, or discoloration due to overheating.
- Skladištenje: Store unused connectors in a dry, clean environment, away from direct sunlight and extreme temperatures, to prevent degradation of materials.
Rješavanje problema
This section addresses common issues that may arise with electrical connectors.
| Problem | Mogući uzrok | Rješenje |
|---|---|---|
| Intermitent Connection | Poorly soldered joint, bent pin, debris in contact area, loose mating connector. | Re-solder joint, straighten/replace bent pin, clean contacts, ensure mating connector is fully seated. |
| Nema veze | Open circuit, incorrect wiring, damaged connector, incompatible mating connector. | Check circuit continuity, verify wiring diagram, replace damaged connector, ensure correct mating part. |
| Connector Overheating | Exceeding current rating, poor contact resistance, short circuit. | Verify current draw is within specifications, inspect contacts for corrosion, check for short circuits in the system. |
If issues persist, consult a qualified electronics technician or contact Molex technical support.
Specifikacije
Key specifications for the Molex KK 396 Series Connector, Model 09-48-1054:
- Vrsta proizvoda: Receptacle Connector
- Broj pozicija: 5
- Broj redova: 1
- Pitch Spacing: 3.96mm
- Sistem konektora: Od ploče do ploče
- Vrsta montaže: Through Hole Mount Right Angle
- Kontaktni materijal: Phosphor Bronze
- Kontakt oplata: Tin
- Raspon proizvoda: KK 396 41815 Series
- Usklađen sa RoHS: Da
For complete technical specifications, refer to the official Molex datasheet for part number 09-48-1054.
Garancija i podrška
This product is manufactured by Molex. For information regarding product warranty, technical support, or specific application guidance, please refer to the official Molex webstranice ili kontaktirajte njihov odjel za korisničku podršku.
Napomena: The return policy for this item is non-cancelable and non-returnable as per the seller's terms at the time of purchase. This does not affect any manufacturer's warranty that may apply.
Molex Official Webstranica: www.molex.com